31 Jan ASTM D describes six methods used to test the adhesion strength of pressure sensitive tape. Learn how to test pressure sensitive adhesive tapes to ASTM D with the best equipment. “These test methods are under the jurisdiction of ASTM Committee D on. Packaging published as D – 76 Last previous cdition D/DM –
|Published (Last):||10 August 2009|
|PDF File Size:||1.25 Mb|
|ePub File Size:||6.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
Adhere the tape specimen onto the test panel using a handheld roller. When testing liner astm d3330 adhesion, the face side adhesive is adhered to a thin polyester film. For ASTM D, we would configure a small capacity load cell 10 or astm d3330 pound for this low force peel test.
In a liner-side application, the transfer tape is applied to a strip of 0. Pneumatic grips are useful wstm easily aligning your specimen to astm d3330 any rubbing issues. Rated to N 50 lbf Maximum specimen thickness of 8 mm 0.
ASTM D is d330 of the more popular testing standards to determine the adhesive strength of pressure sensitive tapes.
ASTM D / DM – 04() Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
Have a question about conducting the test for this standard? This is because the measured peel force is not normalized for a fixed area astm d3330 stress.
The 25mm wide jaws are better for aligning smaller sample sizes. The information below should help you understand the basic test procedures and the equipment required to meet this standard with accuracy. In this test a astm d3330 of f3330 astm d3330 applied to a rigid substrate and then another strip of tape is applied to the backing of the first strip, then tested for peel adhesion.
Testing is then conducted for degree peel adhesion. These test methods may not provide design information as there is usually no direct relationship between peel adhesion and any functional requirement. For this test we recommend that care be taken in aligning the grips to prevent the backside of the tape specimen from rubbing. The tape is then pulled from the plate at a degree angle at a specified rate, and peel adhesion astm d3330 measured.
This test also measures peel adhesion with a degree peel. This plot will be an important aspect of data retrieval and therefore we highly recommend our XyPlot software. The tape astm d3330 peeled astm d3330 the panel at 90 degree angle at a constant speed, astm d3330 which time the force required to effect peel is measured.
ASTM D Peel Adhesion of Pressure Sensitive Tape How to Guide – ADMET
Repeat astm d3330 1 to 6 of Test Method A. We are confident that we have what you are looking for. This unique standard consists of Methods A through F, identifying ways to measure peel adhesion with degree and 90 degree peel methods. Secure the tab to the static grip. The data from this test measures the uniformity of adhesion of a pressure sensitive tape. GK Mechanical Vice Grip. The force will be astm d3330 at other peel rates.
ASTM D3330 Peel Adhesion Pressure Sensitive Adhesive Tapes
If you would rather see the data in real-time and study the peel interface at the astm d3330 time, we would provide you with our XyLive Software. Fold a tab of the tape and double back astm d3330 an angle of degrees. These test methods are tools for quality assurance use. If the adherent is set on an angle, that will cause an error.
Test Method A, B, C, E, or F can show the relative bond strength of a given tape to one or more surfaces material and texture as compared to the standard stainless steel panel.
ASTM D3330 Peel Adhesion of Pressure Sensitive Tape How to Guide
The liner is peeled from the adhesive in the same astm d3330 as in peeling a single-coated tape from a standard panel. The data obtained provide a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive adhesive tape. astm d3330
ASTM D Test Method D astm d3330 a measure of the adherence of the release liner to the astm d3330 of either single- or double-coated tape. We are happy to help! Test Methods A, B, C, E or F cannot be used to compare two pressure-sensitive tapes of the same type but of different manufacture for their ability to adhere to a surface.
ASTM D Test Method D provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive adhesive tape. astm d3330
Although we can provide you with guidance, we recommend you purchase and closely follow the ASTM International testing astm d3330. Test Astm d3330 D can show the amount of force required to remove a liner that covers the adhesive side of a tape at a specified peel rate. Begin peeling the tape at a 90 degree angle.